1995 - 2003 Custom Hydra Tuning - Stock Truck (SDK Performance)
1995 - 2003 Custom Hydra Tuning - Stock Truck (SDK Performance)
If you are ordering tuning for a new Hydra from us, please put "blank" in the serial number selection box.
With SDK Performance Tune's you can get the most out of your 7.3L Powerstroke Diesel. We offer lots of customization and tunes tailored to what you are looking to get out of your truck.
Below is a list of all the available tunes that we can quickly program into your pre-existing Hydra Tuner Chip. You can pick up to 6 different selectable on-the-fly tunes that will be loaded onto your chip.
Whisper mode
Quiets the truck down for going through the drive thru. On PCM codes that allow it, this can now be used as a no start option. **Note: Do not use until truck is warmed to operating temperature**
Designated High Idle
Customer can choose what RPM they would like this set at. Most common is 1100RPM but this is variable between 900-1500RPM. We offer a split High Idle so when cold it will only idle at the selected RPM until warm, once it reaches operating temperature it can bump up 200-400RPM to run a PTO, welder, winch, etc.
EOT Kick
Allows high idle to engage after time based value (chosen by customer) and once computer sees brake pedal input it kicks down to normal idle and can be driven.
3in1 Tune
High idle to set rpm until it reaches 140* then it becomes your stock file (or any file you choose). For the Superduty models there is a 3in1 tune, that when off and that position is selected it won't start. However start the truck in the other positions and flip back into it the tune becomes your high idle till it reaches 140*, then it's your stock tune. **This Tune is for select PCM codes only, Please check the FAQ to see if this tune will work with your truck**
Valet Tune
Limit vehicle speed and RPM's
"Dead Pedal" Tune
When this position is selected, your truck will start and idle as normal, but the throttle pedal will have no input until another position is selected
Various Tow Tunes
Heavy Tow
Low end fuel increase with extended shift points for max capacity towing
Tow
SDK Performances most common tow file for do it all tow duty. An increase in power on the low end all the way through the mid range combined with extended shifting and lock up strategies make this a good option for near any size load
Light Tow
Intended for smaller trailers and light loads like pulling your flat deck and small car. Similar shifting as the Tow file with increased top end fueling.
SuperTow
Written specifically for light loads. Where a slightly extended shift point is needed with similar fueling to a daily file. Works best for sled decks and quads or a full box.
Economy/Daily Duty Tunes
DailyReduced - The mildest of daily files, best suited for fuel economy with added pep.
Daily - Very linear power curve, smooth shifting with enough top end fuel to have fun with, all while keeping smoke to a minimum.
StealthBomber - A Jekyll and Hyde version of the Daily file. Exactly the same tune with a late fuel curve to have a good amount more kick on the top end.
Performance/Hot Tune
RoidRager - Specifically written for the manual trans guys. This peformance tune uses the MAP sensor to limit low end fueling. Drives very similar to a stock file until you put the throttle down where it becomes one under a race file.
StreetRocker - The StreetRocker was created with driveability in mind. Good low end response with excellent midrange and top end power.
HippieKiller - SDK Performances flagship Race file. No explanation needed
ZombieKiller - In case HippieKiller wasn’t enough. A more aggressive curve is available. Best suited for Dyno or Nitrous use.
SledRocker - All the fuel you could ask for to keep that turbine wheel spinning with custom shift/lockup strategies for the Sled.
Custom Drag/Pull/Specific Tunes
Tailored drag and/or pull tunes can also be done to customer specifications on shifting and lockup. If requested, higher rpm and extra fuel can also be added.
Show Tunes
ZombieLope - Exactly as it sounds. Aggressive low end fueling with hard sharp lope.
-
Delivery/Revisions
All ECM calibrations are delt with on a first come first serve basis. Most requests will be completed within 24-72 hours. Revisions should be requested through email and will be accommodated accordingly to the request. WRONG DEVICE OR VEHICLE INFOMATION PROVIDED AFTER THE TUNE IS WRITTEN WILL RESULT IN A FEE TO REVISE*
-
Disclaimer:
Peakside Performance is not responsible for damage resulting from any modification performed by, produced by or recommended by us. Buyer assumes all risk for modifications and is responsible for any mechanical failures resulting from these modifications. Completely stock vehicles break every day for no reason.